|
|
Home |
Computers |
Networks |
Cisco CCNA / CCNP: H ...
Cisco CCNA / CCNP: How And Why To Build An Etherchannel
Submitted by Chris on 2006-02-15 and viewed 208 times.
|
|
|
 Rate This Article |
 Add Comments |
 Send To Friends|
View Comments (0)
Publisher |
 Print
| |
|
Etherchannels are in use all over the world, as well as on your CCNA and CCNP exams. Learn how to build and support an EC in this tutorial from Chris Bryant, CCIE #12933.
|
|
|
CCNA and CCNP candidates are well-versed in Spanning-Tree Protocol, and one of the great things about STP is that it works well with little or no additional configuration. There is one situation where STP works against us just a bit while it prevents switching loops, and that is the situation where two switches have multiple physical connections.
You would think that if you have two separate physical connections between two switches, twice as much data could be sent from one switch to the other than if there was only one connection. STP doesn't allow this by default, however in an effort to prevent switching loops from forming, one of the paths will be blocked.
SW1 and SW2 are connected via two separate physical connections, on ports fast0/11 and fast 0/12. As we can see here on SW1, only port 0/11 is actually forwarding traffic. STP has put the other port into blocking mode (BLK).
SW1#show spanning vlan 10
(some output removed for clarity)
Interface Role Sts Cost Prio.Nbr Type
Fa0/11 Root FWD 19 128.11 P2p
Fa0/12 Altn BLK 19 128.12 P2p
While STP is helping us by preventing switching loops, STP is also hurting us by preventing us from using a perfectly valid path between SW1 and SW2. We could literally double the bandwidth available between the two switches if we could use that path that is currently being blocked.
The secret to using the currently blocked path is configuring an Etherchannel. An Etherchannel is simply a logical bundling of 2 - 8 physical connections between two Cisco switches.
Configuring an Etherchannel is actually quite simple. Use the command "channel-group 1 mode on" on every port you want to be placed into the Etherchannel. Of course, this must be done on both switches if you configure an Etherchannel on one switch and don't do so on the correct ports on the other switch, the line protocol will go down and stay there.
The beauty of an Etherchannel is that STP sees the Etherchannel as one connection. If any of the physical connections inside the Etherchannel go down, STP does not see this, and STP will not recalculate. While traffic flow between the two switches will obviously be slowed, the delay in transmission caused by an STP recalculation is avoided. An Etherchannel also allows us to use multiple physical connections at one time.
Here's how to put these ports into an Etherchannel:
SW1#conf t
Enter con
figuration commands, one per line. End with CNTL/Z.
SW1(config)#interface fast 0/11
SW1(config-if)#channel-group 1 mode on
Creating a port-channel interface Port-channel 1
SW1(config-if)#interface fast 0/12
SW1(config-if)#channel-group 1 mode on
SW2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW2(config)#int fast 0/11
SW2(config-if)#channel-group 1 mode on
SW2(config-if)#int fast 0/12
SW2(config-if)#channel-group 1 mode on
The command "show interface trunk" and "show spanning-tree vlan 10" will be used to verify the Etherchannel configuration.
SW2#show interface trunk (some output removed for clarity)
Port Mode Encapsulation Status Native vlan
Po1 desirable 802.1q trunking 1
SW2#show spanning vlan 10 (some output removed for clarity)
Interface Role Sts Cost Prio.Nbr Type
Po1 Desg FWD 12 128.65 P2p
Before configuring the Etherchannel, we saw individual ports here. Now we see "Po1", which stands for the interface "port-channel1". This is the logical interface created when an Etherchannel is built. We are now using both physical paths between the two switches at one time!
That's one major benefit in action let's see another. Ordinarily, if the single open path between two trunking switches goes down, there is a significant delay while another valid path is opened - close to a minute in some situations. We will now shut down port 0/11 on SW2 and see the effect on the etherchannel.
SW2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW2(config)#int fast 0/11
SW2(config-if)#shutdown
3w0d: %LINK-5-CHANGED: Interface FastEthernet0/11, changed
state to administratively down
SW2#show spanning vlan 10
VLAN0010
Spanning tree enabled protocol ieee
Interface Role Sts Cost Prio.Nbr Type
Po1 Desg FWD 19 128.65 P2p
SW2#show interface trunk
Port Mode Encapsulation Status Native vlan
Po1 desirable 802.1q trunking 1
The Etherchannel did not go down! STP sees the Etherchannel as a single link therefore, as far as STP is concerned, nothing happened.
Building an Etherchannel and knowing how it can benefit your network is an essential skill for CCNA and CCNP success, and it comes in very handy on the job as well. Make sure you are comfortable with building one before taking Cisco's exams!
|
|
Article Source: http://www.awesomewebessentials.com/
Article Tags:
ccna|
pass|
free|
exam|
icnd|
intro|
ccnp|
etherchannel|
switch|
root|
bridge|
chris|
bryant|
ccie|
Bookmark This Articles:
del.icio.us
*
Digg it
*
Furl
* reddit
* Spurl
* Yahoo MyWeb
|
|
Chris Bryant, CCIE #12933, owns The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials, Pass the CCNA exam with Chris Bryant! |
|
|
|
Print Files, Images and Documents to Any Printer Worldwide for Free with PrinterAnywhere’s New Service
Home Wireless Network Security Issues
Cisco CCNA / CCNP Certification Exam: Creating A Study Plan
Cisco CCNA / CCNP Tutorial: Home Lab Assembly Case Study
Cisco CCNA Certification: Four Tips To Use DURING The Exam
Cisco CCNP / BSCI Certification: Troubleshooting Route Redistribution, Part I
Cisco CCNA / CCNP Home Lab Setup: How To Configure Reverse Telnet
CCNA / CCNP Home Lab Tutorial: Assembling Your Cisco Home Lab
Cisco CCNA / CCNP Certification: Deciphering Ping Results
Cisco CCNA Certification: Static Routing Tutorial
Cisco CCNA Certification: Defining And Creating Collision Domains
Passing The CCNA and CCNP Exams: Setup Mode
Cisco CCNA / CCNP Certification: OSPF E2 vs. E1 Routes
Cisco CCNA / CCNP Certification: How And Why To Build An Etherchannel
Cisco CCNP / BSCI Certification: Route Redistribution And The Seed Metric
Cisco CCNA Certification: How And Why Switches Trunk
Passing Cisco's CCNA and CCNP Exams: The VLAN.DAT File
Cisco CCNA / CCNP Home Lab Tutorial: A Guide To Cable Types
Learning To Navigate Cisco's Online Documentation Website
Cisco CCNA Certification: Defining Broadcast Domains
Three Ways To Jumpstart Your IT Career
|
| |
|
|
|
|
|
|
